Lakb50 Posted December 11, 2022 Share Posted December 11, 2022 I would like to raise my 48 inch metal stand so the lower shelf is higher off the ground. The stand holds 1 - 40 long and 1 - 33 long. How can I safely raise it? I am getting to old to sit on the floor to do maintenance. Thank You…….. Lisa Link to comment Share on other sites More sharing options...
nabokovfan87 Posted December 11, 2022 Share Posted December 11, 2022 @Lakb50 What does the stand look like? How is it made? Is it like a storage rack unit? Link to comment Share on other sites More sharing options...
Lakb50 Posted December 11, 2022 Author Share Posted December 11, 2022 It’s a store bought welded aquarium stand with the scroll sides. 2 Link to comment Share on other sites More sharing options...
Patrick_G Posted December 11, 2022 Share Posted December 11, 2022 Nice looking stand. I guess your best bet would be to have a local fabrication shop weld another shelf, but cost and hassle would probably make that impractical. I think I'd make a short wooden shelf that fits inside the lower space. Something like this but homemade out of pine 1” stock. Link to comment Share on other sites More sharing options...
pseudomugil Posted December 12, 2022 Share Posted December 12, 2022 If you decide on going through a fabrication shop, make sure they are aware of how much weight will be on the stand and that it must be level. A few cinderblocks though would be much cheaper than typical hourly at a fab shop, if you value function over form and are on a budget. 1 Link to comment Share on other sites More sharing options...
Lakb50 Posted December 12, 2022 Author Share Posted December 12, 2022 I want to raise the whole unit not just the bottom shelf. Would cinder blocks be strong enough to hold 73 gallons? Link to comment Share on other sites More sharing options...
gardenman Posted December 12, 2022 Share Posted December 12, 2022 On 12/12/2022 at 6:57 AM, Lakb50 said: I want to raise the whole unit not just the bottom shelf. Would cinder blocks be strong enough to hold 73 gallons? As is often the case, it depends. Cinder blocks are very strong in some directions (the solid parts) and not as strong in other parts (the hollow parts.) If you were able to park you stand atop the solid parts, it would easily hold the 73 gallons. If the legs were over the hollow parts, eh, it gets trickier. It would probably hold but the risk of failure grows. Solid concrete blocks instead of cinder blocks would definitely be strong enough. Link to comment Share on other sites More sharing options...
mynameisnobody Posted December 12, 2022 Share Posted December 12, 2022 You can use cinder blocks with a 1” sheet of plywood running across it, this should disperse the weight over the whole board rather than 1 spot on the block. Also, you can paint the blocks to match. Link to comment Share on other sites More sharing options...
pseudomugil Posted December 12, 2022 Share Posted December 12, 2022 I can’t remember if the shelves of these stands are made from angle or square tubing, but I wouldn’t worry about the legs resting on the cinderblocks. Just support the long runs of the lower shelf with cinderblock in the correct orientation and let the legs wrap around the sides. Hard to explain without a picture, maybe. @gardenman has a point by going under the legs with solid blocks. That could also maximize space under the stand for storage, etc. Link to comment Share on other sites More sharing options...
Lakb50 Posted December 12, 2022 Author Share Posted December 12, 2022 Is the solid part stronger than the hollow side? Thank you all for your help. Lisa Link to comment Share on other sites More sharing options...
JettsPapa Posted December 12, 2022 Share Posted December 12, 2022 On 12/12/2022 at 8:32 AM, Lakb50 said: Is the solid part stronger than the hollow side? Thank you all for your help. Lisa The strongest way to set them up is with the holes running vertical (top to bottom). That way all of the weight is directly supported all the way down. If you turn them the other way and there's a load above one of the holes they can collapse. On 12/12/2022 at 7:57 AM, Mynameisnobody said: You can use cinder blocks with a 1” sheet of plywood running across it, this should disperse the weight over the whole board rather than 1 spot on the block. Also, you can paint the blocks to match. I agree about covering the cinder blocks with plywood, but I've never seen 1" thick plywood. I'm not saying it doesn't exist, but if it does it might be difficult to find. 3/4" should be fine. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now