TheMilkman Posted December 24, 2020 Share Posted December 24, 2020 (edited) Hey everyone, my water comming out of my tap is currently a ph of 8.4 with gh of over 300 and kh about the same. How would I use rodi water to lower this? Thanks! Edited December 24, 2020 by TheMilkman Link to comment Share on other sites More sharing options...
AdamTill Posted December 24, 2020 Share Posted December 24, 2020 Replace some of it. That said, I’m breeding otos and cories in basically that same water Link to comment Share on other sites More sharing options...
TheMilkman Posted December 24, 2020 Author Share Posted December 24, 2020 7 hours ago, AdamTill said: Replace some of it. That said, I’m breeding otos and cories in basically that same water So basically do a water change with rodi water instead of tap, what about just topping it off with rodi water? Link to comment Share on other sites More sharing options...
gardenman Posted December 24, 2020 Share Posted December 24, 2020 When water evaporates, the minerals and whatnot stay behind. That why in marine aquariums you top them off with fresh water. To effectively lower your numbers, you need to swap out your water with RO or distilled water. In a water change both the water and the minerals suspended in it leave. In evaporation, just the water leaves, the minerals and whatnot stay behind. Link to comment Share on other sites More sharing options...
tolstoy21 Posted December 24, 2020 Share Posted December 24, 2020 As far as I’m aware, topping off the water with rodi only has the effect mitigating the upward climb of some of your measurable water parameters if you have nothing else in the tank to actively reduce them, as water evaporation will tend to concentrate things. To dilute the water you need to replace an portion of water with rodi. Link to comment Share on other sites More sharing options...
TheMilkman Posted December 24, 2020 Author Share Posted December 24, 2020 9 minutes ago, gardenman said: When water evaporates, the minerals and whatnot stay behind. That why in marine aquariums you top them off with fresh water. To effectively lower your numbers, you need to swap out your water with RO or distilled water. In a water change both the water and the minerals suspended in it leave. In evaporation, just the water leaves, the minerals and whatnot stay behind. Ahhh, ok thank you very much. Link to comment Share on other sites More sharing options...
TheMilkman Posted December 24, 2020 Author Share Posted December 24, 2020 7 minutes ago, tolstoy21 said: As far as I’m aware, topping off the water with rodi only has the effect mitigating the upward climb of some of your measurable water parameters if you have nothing else in the tank to actively reduce them, as water evaporation will tend to concentrate things. To dilute the water you need to replace an portion of water with rodi. Thank you so much Link to comment Share on other sites More sharing options...
TheMilkman Posted December 24, 2020 Author Share Posted December 24, 2020 When using ro water to replace, would you slowly add it as not to shock any of the fish and shrimp? Link to comment Share on other sites More sharing options...
gardenman Posted December 24, 2020 Share Posted December 24, 2020 1 hour ago, TheMilkman said: When using ro water to replace, would you slowly add it as not to shock any of the fish and shrimp? Slower is always better (well almost always.) The exceptions to that would be if your fish were in dire distress or you're trying to encourage a fish to spawn. Then sometimes you want a more drastic change in water temp/chemistry as if it were the rainy season and they were having a downpour. Even then a somewhat more moderate pace isn't bad. On some of my tanks I'll set up a bottle full of replacement water and then just let a length of airline tubing drip it into the tank. I'm doing that now with my twenty high as my breeder box full of baby plecos is on that tank and I don't want to unduly shock them. Link to comment Share on other sites More sharing options...
TheMilkman Posted December 24, 2020 Author Share Posted December 24, 2020 22 minutes ago, gardenman said: Slower is always better (well almost always.) The exceptions to that would be if your fish were in dire distress or you're trying to encourage a fish to spawn. Then sometimes you want a more drastic change in water temp/chemistry as if it were the rainy season and they were having a downpour. Even then a somewhat more moderate pace isn't bad. On some of my tanks I'll set up a bottle full of replacement water and then just let a length of airline tubing drip it into the tank. I'm doing that now with my twenty high as my breeder box full of baby plecos is on that tank and I don't want to unduly shock them. Ok, i think ill do that then. Link to comment Share on other sites More sharing options...
AquaticJ Posted December 27, 2020 Share Posted December 27, 2020 Is there a reason you want to lower those? Most species will be totally fine in that current water. The reason I ask is because it becomes a huge headache just to do a water change. You’ll have to mix the right amount of RO with tap to achieve the desired Gh, Kh, pH, and then use that mix everytime you change the water. 1 Link to comment Share on other sites More sharing options...
TheMilkman Posted January 2, 2021 Author Share Posted January 2, 2021 Yes, i am trying to breed apistogramma and they need significantly lower water hardness and ph. Link to comment Share on other sites More sharing options...
TheMilkman Posted January 2, 2021 Author Share Posted January 2, 2021 On 12/26/2020 at 10:36 PM, AquaticJ said: Is there a reason you want to lower those? Most species will be totally fine in that current water. The reason I ask is because it becomes a huge headache just to do a water change. You’ll have to mix the right amount of RO with tap to achieve the desired Gh, Kh, pH, and then use that mix everytime you change the water. Yes, i am trying to breed apistogramma and they need significantly lower water hardness and ph. Link to comment Share on other sites More sharing options...
lefty o Posted January 2, 2021 Share Posted January 2, 2021 i know most around here get all worked up over a water softener, but if i wanted to lower hardness, and ph, i would install a water softener post haste. just my opinion. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now